安装完vsftpd后,默认情况下,CentOS的防火墙是不开放ftp服务的,需要添加模块和开放21端口才能提供ftp访问。1.添加ip_conntrack_ftp 模块[root@hexuweb101 ~] vi /etc/sysconfig/iptables-config添加下面一行IPTABLES_MODULES="ip_conntrack_ftp"2.打开21端口[root@hexuweb101 ~] vi /etc/sysconfig/iptablesCentOS 5.x版本添加如下规则-A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 21 -j ACCEPTCentOS 6.x...
转自:http://www.woxplife.com/articles/404.html虽说阿里云推出了云盾服务,但是自己再加一层防火墙总归是更安全些,下面是我在阿里云vps上配置防火墙的过程,目前只配置INPUT。OUTPUT和FORWORD都是ACCEPT的规则一、检查iptables服务状态首先检查iptables服务的状态1 [root@woxplife ~]# service iptables status
2 iptables: Firewall is not running.说明iptables服务是有安装的,但是没有启动服务。如果没有安装的话可以直接y...
CentOS下配置防火墙 配置nat转发服务CentOS下配置iptables防火墙linux NAT(iptables)配置CentOS下配置iptables 1,vim /etc/sysconfig/network 这里可以更改主机名称。NETWORKING=yesNETWORKING_IPV6=noHOSTNAME=BGI-TJ.localdomain GATEWAY=192.168.11.1(超算网关) 2.vim /etc/sysconfig/network-scripts/ifcfg-eth0 第一块网卡。Broadcom Corporation NetXtreme II BCM5709 Gigabit EthernetDEVICE=eth0BOOTPROTO=staticHWADDR...
1、直接关闭防火墙systemctl stop firewalld.service; #停止firewallsystemctl disable firewalld.service; #禁止firewall开机启动2、安装并启动 iptables service,以及设置开机自启yum -y install iptables-services;#安装iptablessystemctl start iptables;#启动iptablessystemctl enable iptables;#自启动iptablessystemctl start ip6tables;#启动ip6tables(不需要可以跳过)systemctl enable ip6tables;#自启动ip6tab...
测试环境操作系统:CentOS 7.7代理服务器 内:10.0.0.1 外:192.168.31.200FTP服务器 内:10.0.0.2以下操作均在代理服务器上操作#00、测试源机器FTP正常,代理机器ftp访问ftp服务器正常ftp 10.0.0.2test123456#01、开放20和21的TCP端口iptables -I INPUT -m state --state NEW -m tcp -p tcp --dport 20:21 -j ACCEPT#02、永久开启iptables的ftp转发模块(用于IP NAT转换)cat >>/etc/sysconfig/iptables-config<<EOFIPTABLES_MODU...
场景:在本地虚拟机上使用ftp软件需要进行相应的端口设置,不可避免要访问Cnetos的防火墙,默认firewall操作不方便,所以需要进行相应的替换。1 配置防火墙,开启80端口、3306端口1.1 配置iptablesCentOS 7 默认使用firewalld来管理iptables规则,由于防火墙规则变动的情况很少,动不动态变得无所谓了。但是习惯是魔鬼,跟之前不一样,总是感觉不太习惯。systemctl disable firewalld
yum remove firewalld -y使用下面的办法来恢复...
我们在生产环境中,一般都是把防火墙打开的,不像测试环境,可以直接关闭掉。最近安装zabbix ,由于公司服务器既有centos 7又有centos 6,遇到了一些防火墙的问题,现在正好把centos防火墙的问题梳理一下,做一个记录。开放其他端口同理,只需要把我这里的10050修改为其他需要开放的端口即可。 一、CentOS 7 如果打开了防火墙,需要在firewalld中添加策略,允许访问zabbix-agent端口10050和10051以下是添加zabbix端口10050和10051...
http://www.cnblogs.com/metoy/p/4320813.html CentOS 7.0默认使用的是firewall作为防火墙,使用iptables必须重新设置一下1、直接关闭防火墙systemctl stop firewalld.service #停止firewallsystemctl disable firewalld.service #禁止firewall开机启动2、设置 iptables serviceyum -y install iptables-services如果要修改防火墙配置,如增加防火墙端口3306vi /etc/sysconfig/iptables 增加规则-A INPUT -m state --state NEW -m ...
今天安装了一个centos 6.9 ,查看默认python版本是2.6,所以准备升级,按着以前在ubuntu上的升级步骤:(1) wget http://www.python.org/ftp/python/3.3.0/Python-3.3.0.tgz(2) tar -xzvf Python-3.3.0.tgz(3) mkdir /usr/local/python(4) ./configure --prefix=/usr/local/python3 在第四步出现了一个提示: 提示:configure: error: no acceptable C compiler found in $PATH 原来是缺少C编译器,需要安装GCC套件,于是采...
一、配置防火墙,开启80端口、3306端口CentOS 7.0默认使用的是firewall作为防火墙,这里改为iptables防火墙。1、关闭firewall:systemctl stop firewalld.service #停止firewallsystemctl disable firewalld.service #禁止firewall开机启动 2、安装iptables防火墙yum install iptables-services #安装 显示ok以后,就表示已经安装成功,那么就继续执行下面 vi /etc/sysconfig/iptables #编辑防火墙配置文件# Firewall configurati...
操作系统环境:CentOS Linux release 7.0.1406(Core) 64位CentOS 7.0默认使用的是firewall作为防火墙,这里改为iptables防火墙步骤。1、关闭firewall:systemctl stop firewalld.service #停止firewallsystemctl disable firewalld.service #禁止firewall开机启动firewall-cmd --state #查看默认防火墙状态(关闭后显示notrunning,开启后显示running)2、iptables防火墙(这里iptables已经安装,下面进行配置)vi/etc/sysconfig/i...
开启访问端口Linux版本:CentOS release 6.9 此处以nginx访问端口8081为例编辑:vi /etc/sysconfig/iptables添加:-A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 8081 -j ACCEPT重启服务:/etc/init.d/iptables restart检查端口是否开放:/sbin/iptables -L -n 其他的方法service iptables stopservice iptables start 原文:https://www.cnblogs.com/xuchen0117/p/11881428.html
cd先将服务器防火墙80级8850端口打开临时关闭SELinux/防火墙setenforce 0iptables -F重点 重点 不能用root用户安装 不能用root用户安装 第一步先创建一个安装用户登录root用户添加组#添加组groupadd tableau#添加安装用户useradd admin -g tableau#设置用户密码并激活passwd admin 添加普通用户具有sudo权限修改 /etc/sudoers 需要使用 visudo 指令visudo添加代码a键可以进入编辑模式,移动光标至文末加入以下代码admin ALL=(ALL)...
最近在玩nginx作为图片服务器,在Sentos上安装后发现访问不了虚拟机,发现是80端口没开。找到一篇不错的文章 http://linux.it.net.cn/CentOS/fast/2015/0110/11567.html 一、配置防火墙,开启80端口、3306端口CentOS 7.0默认使用的是firewall作为防火墙,这里改为iptables防火墙。1、关闭firewall:systemctl stop firewalld.service #停止firewallsystemctl disable firewalld.service #禁止firewall开机启动Linux学习,http:// ...
iptables nginx fastCGI 网站环境:Centos nginx php(wordpress) 现在的问题总结如下: 启动iptables网站返回502,关闭iptables网站打开正常 iptables 设置如下: Chain INPUT (policy DROP 1 packets, 139 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- lo any anywhere anywhere ...