首页 / 网络知识 / Cisco交换机综合配置实例(一)
Cisco交换机综合配置实例(一)
网络教程导读
互联网集市收集整理了【Cisco交换机综合配置实例(一)】路由器上网教程,小编现在分享给大家,供广大互联网技能从业者学习和参考。文章包含7444字,纯文字阅读大概需要11分钟。
网络教程内容图文
本实例综合性很强,基本上包含了Cisco交换机的所有交换技术
1. 网络拓扑和相应设计
目录:
网络配置实例
网络拓扑和相应设计
Catalyst 5509 配置
Catalyst 4003 配置
RSM 配置
Catalyst 5505 配置
网络拓扑和相关设计
网络拓扑图
2. Catalyst 5509 的配置
下面列出 Catalyst 5509 的基本配置
Enter passWord:
Console> enable
Enter password:
Console> (enable) set system name 5509-ER-F1
System name set.
5509-ER-F1> (enable) set system location 1st Floor Equipment Room
System location set.
5509-ER-F1> (enable) set system contact sysadmin@bigcorp.com
System contact set.
5509-ER-F1> (enable) set time 04/30/1999 9:30:00
Fri Apr 30 1999, 09:30:00
5509-ER-F1> (enable) set password
Enter old password:
Enter new password:
Retype new password:
Password changed.
5509-ER-F1> (enable) set enablepass
Enter old password:
Enter new password:
Retype new password:
Password changed.
5509-ER-F1> (enable) set banner motd %
5509-ER-F1 (Catalyst 5509)
Access Restricted
%
MOTD banner set
5509-ER-F1> (enable) set interface sc0 10.10.1.10/24
Interface sc0 IP address set.
5509-ER-F1> (enable) set ip route default 10.10.1.1
Route added.
5509-ER-F1> (enable) set ip dns server 10.10.10.100
10.10.10.100 added to DNS server table as primary server.
5509-ER-F1> (enable) set ip dns domain bigcorp.com
Default DNS domain name set to bigcorp.com
5509-ER-F1> (enable) set ip dns enable
DNS is enabled
5509-ER-F1> (enable) set vtp domain BigCorp mode server
VTP domain BigCorp modified
5509-ER-F1> (enable) set vlan 10 name Corporate
Vlan 10 configuration sUCcessful
5509-ER-F1> (enable) set vlan 20 name DevEng
Vlan 20 configuration successful
5509-ER-F1> (enable) set vlan 30 name Mfg
Vlan 30 configuration successful
5509-ER-F1> (enable) set vlan 40 name QA
Vlan 40 configuration successful
5509-ER-F1> (enable) set vlan 50 name Finance&Admin
Vlan 50 configuration successful
5509-ER-F1> (enable) set vlan 60 name Sales&Mktg
Vlan 60 configuration successful
5509-ER-F1> (enable) set module name 1 Supervisor III
Module name set.
5509-ER-F1> (enable) set port flowcontrol 1/1-2 send off
Ports 1/1-2 flow control send administration status set to off
(ports will not send flowcontrol to far end)
5509-ER-F1> (enable) set port flowcontrol 1/1-2 receive off
Ports 1/1-2 flow control receive administration status set to off
(ports will not allow far end to send flowcontrol)
5509-ER-F1> (enable) set port negotiation 1/1-2 enable
Ports 1/1-2 negotiation enabled
5509-ER-F1> (enable) set port name 1/1-2 GEC 802.1Q Trunk
Ports 1/1-2 name set.
5509-ER-F1> (enable) set port channel 1/1-2 desirable
Port(s) 1/1-2 channel mode set to desirable.
5509-ER-F1> (enable) set trunk 1/1 desirable dot1q
Port(s) 1/1 trunk mode set to desirable.
Port(s) 1/1 trunk type set to dot1q.
5509-ER-F1> (enable) set module name 3 RSM (RSM-ER-F1)
Module name set.
5509-ER-F1> (enable) set module name 5 Fast Ether Uplinks
Module name set.
5509-ER-F1> (enable) set port name 5/1-4 FEC ISL Trunk
Ports 5/1-4 name set.
5509-ER-F1> (enable) set port speed 5/1-4 100
Ports 5/1-4 transmission speed set to 100Mbps.
5509-ER-F1> (enable) set port duplex 5/1-4 full
Ports 5/1-4 set to full-duplex.
5509-ER-F1> (enable) set port flowcontrol 5/1-4 send off
Ports 5/1-4 flow control send administration status set to off
(ports will not send flowcontrol to far end)
5509-ER-F1> (enable) set port flowcontrol 5/1-4 receive off
Ports 5/1-4 flow control receive administration status set to off
(ports will not allow far end to send flowcontrol)
5509-ER-F1> (enable) set port negotiation 5/1-4 enable
Ports 5/1-4 negotiation enabled
5509-ER-F1> (enable) set port channel 5/1-4 desirable
Port(s) 5/1-4 channel mode set to desirable.
5509-ER-F1> (enable) set trunk 5/1 desirable isl
Port(s) 5/1 trunk mode set to desirable.
Port(s) 5/1 trunk type set to isl.
5509-ER-F1> (enable) set module name 6 DevEng 100Mb Hosts
Module name set.
5509-ER-F1> (enable) set port name 6/1 DE Sparc Ultra
Port 6/1 name set.
5509-ER-F1> (enable) set port name 6/2-7 DE Sparc20
Ports 6/2-7 name set.
5509-ER-F1> (enable) set port name 6/8-12 DE NT Workstation
Ports 6/8-12 name set.
5509-ER-F1> (enable) set port speed 6/1-12 100
Ports 6/1-12 transmission speed set to 100Mbps.
5509-ER-F1> (enable) set port duplex 6/1-12 full
Ports 6/1-12 set to full-duplex.
5509-ER-F1> (enable) set port flowcontrol 6/1-12 send desired
Ports 6/1-12 flow control send administration status set to desired
(ports will send flowcontrol to far end if far end supports it)
5509-ER-F1> (enable) set port flowcontrol 6/1-12 receive desired
Ports 6/1-12 flow control receive administration status set to desired
(ports will allow far end to send flowcontrol if far end supports it)
5509-ER-F1> (enable) set port channel 6/1-12 off
Port(s) 6/1-12 channel mode set to off.
5509-ER-F1> (enable) set trunk 6/1-12 off
Port(s) 6/1-12 trunk mode set to off.
5509-ER-F1> (enable) set spantree portfast 6/1-12 enable
Warning: Spantree port fast start should only be enabled on ports connected
to a single host. Connecting hubs, concentrators, switches, bridges, etc. to
a fast start port can cause temporary spanning tree loops. Use with caution.
Spantree ports 6/1-12 fast start enabled.
5509-ER-F1> (enable) set vlan 20 6/1-12
VLAN 20 modified.
VLAN 1 modified.
VLAN Mod/Ports
---- -----------------------
201/1-2
5/1-4
6/1-12
5509-ER-F1> (enable) set module name 7 Corp/Mfg 10Mb Hosts
Module name set.
5509-ER-F1> (enable) set port name 7/1-12 Corp Win98 PC
Ports 7/1-12 name set.
5509-ER-F1> (enable) set port name 7/13-48 Mfg Win98 PC
Ports 7/13-48 name set.
5509-ER-F1> (enable) set port duplex 7/1-48 full
Ports 7/1-48 set to full-duplex.
5509-ER-F1> (enable) set spantree portfast 7/1-48 enable
Warning: Spantree port fast start should only be enabled on ports connected
to a single host. Connecting hubs, concentrators, switches, bridges, etc. to
a fast start port can cause temporary spanning tree loops. Use with caution.
Spantree ports 7/1-48 fast start enabled.
5509-ER-F1> (enable) set vlan 10 7/1-12
VLAN 10 modified.
VLAN 1 modified.
VLAN Mod/Ports
---- -----------------------
101/1-2
5/1-4
7/1-12
5509-ER-F1> (enable) set vlan 30 7/13-48
VLAN 30 modified.
VLAN 1 modified.
VLAN Mod/Ports
---- -----------------------
301/1-2
5/1-4
7/13-48
5509-ER-F1> (enable) set module name 8 DevEng 10Mb Hosts
Module name set.
5509-ER-F1> (enable) set port name 8/1-48 DevEng WinNT PC
Ports 8/1-48 name set.
5509-ER-F1> (enable) set port duplex 8/1-48 full
Ports 8/1-48 set to full-duplex.
5509-ER-F1> (enable) set spantree portfast 8/1-48 enable
Warning: Spantree port fast start should only be enabled on ports connected
to a single host. Connecting hubs, concentrators, switches, bridges, etc. to
a fast start port can cause temporary spanning tree loops. Use with caution.
Spantree ports 8/1-48 fast start enabled.
5509-ER-F1> (enable) set vlan 20 8/1-48
VLAN 20 modified.
VLAN 1 modified.
VLAN Mod/Ports
---- -----------------------
201/1-2
5/1-4
6/1-12
8/1-48
5509-ER-F1> (enable) set module name 9 DevEng 10Mb Hosts
Module name set.
5509-ER-F1> (enable) set port name 9/1-48 DevEng WinNT PC
Ports 9/1-48 name set.
5509-ER-F1> (enable) set port duplex 9/1-48 full
Ports 9/1-48 set to full-duplex.
5509-ER-F1> (enable) set spantree portfast 9/1-48 enable
Warning: Spantree port fast start should only be enabled on ports connected
to a single host. Connecting hubs, concentrators, switches, bridges, etc. to
a fast start port can cause temporary spanning tree loops. Use with caution.
Spantree ports 9/1-48 fast start enabled.
5509-ER-F1> (enable) set vlan 20 9/1-48
VLAN 20 modified.
VLAN 1 modified.
VLAN Mod/Ports
---- -----------------------
201/1-2
5/1-4
6/1-12
8/1-48
9/1-48
5509-ER-F1> (enable)
网络教程总结
以上是互联网集市为您收集整理的【Cisco交换机综合配置实例(一)】路由器上网教程的全部内容,希望文章能够帮你了解路由器上网教程Cisco交换机综合配置实例(一)。 如果觉得互联网集市路由器上网教程内容还不错,欢迎将互联网集市网站推荐给好友。
网络教程备注
版权声明:本文内容由互联网用户贡献,该文观点与技术仅代表作者本人。本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如发现本站有涉嫌侵权/违法违规的内容, 请发送邮件至 gblab@vip.qq.com 举报,一经查实,本站将立刻删除。
网络教程手机端
扫描二维码推送至手机访问。